Texas Instruments AMC23C11 Precision Isolation comparator has short response time. The open drain output is separated from the input circuit by an anti-magnetic interference isolation barrier. According to VDE 0884-17 and UL1577, the barrier provides enhanced electrical isolation up to 5kV(RMS). It also supports operating voltages up to 1kV(PK).
The Texas Instruments UCC21737-Q1 single-channel gate driver is an electrically isolated gate driver designed for use with SiC MOSFets and IGBTs at DC operating voltages up to 2121V, with advanced protection features, best-in-class dynamic performance and robustness. The device has a peak source and convergent current of up to ±10A.
The AS7331 is an integrated UV sensor with low power and low noise. The three channels, namely UVA, UVB and UVC, convert the optical radiation signal into digital signal through photodiode, realizing a new optical radiation transmission mode of continuous or triggered measurement Irradiation responsivity can be adjusted by gain, conversion time and internal clock frequency to affect sensitivity, full range and LSB.
Flex Power Modules is now available with BMR320, a non-isolated, non-regulated DC-DC intermediate bus converter with a fixed 8:1 input/output voltage ratio and compact appearance. Operating in the 40-60 VDC input voltage range, the product produces an output voltage of 5 to 7.5 VDC, ideal for powering point-of-load converters at lower intermediate bus voltages to optimize system efficiency.
Vishay Intertechnology, Inc, announced the launch of Vishay's first 19.0mm x 17.1mm x 7.0mm 6767 high temperature inductor with A current rating up to 155 A and in compliance with the AEC-Q200 standard. Suitable for applications such as automotive engine nacles and advanced driver assistance systems (ADAS), the DC internal resistance (DCR) is 50 percent lower than that of normal power inductors and is smaller in size than similar ferrite solutions.
The DCF filter series is from ECS Inc. International and is developed with an eye to the future. These high performance ceramic monolithic bandpass filters provide low insertion loss without compromising performance. DCF series filters cover center frequencies from 5235 MHz to 5850 MHz, providing bandwidth from 180 MHz to 1200 MHz, and a series of extension products are forthcoming.
Flex Power Modules' PIM4610 and PIM4710 pci simplify blade server design based on advanced tca standards and other applications. PIM4x10 modules are rated for power up to 1080 W with an efficiency level of up to 98.8%. They have input ranges from 36 V(DC) to 75 V(DC). The module is an industry standard quarter brick sized package featuring unique PIM nails.
TAS2110 is a class H boost in QFN package of 11V amplifier with algorithm control for digital input class D audio. Future algorithms are expected to optimize the boost voltage level to match the output of audio signals. This provides all the power required for peak output while lowering the average value with a constant output lift. The algorithm is configured using the PurePath console GUI.
The AD5770R is a 6-channel, 14-bit resolution, low-noise, programmable current-output digital-to-analog converter (DAC) for photonics control applications. The device includes a 1.25V, on-chip voltage reference, 2.5kΩ precision resistor reference current generation, die temperature, output monitoring function, fault alarm, and reset function.
Maxim's MAX98390 is a highly efficient single Class d DSM intelligent amplifier with integrated boost converter, integrated DSM and FET calibration capabilities to achieve higher efficiency at low output power. Maximum boost converter output voltages can be programmed from 6.5V to 10V, with 0.125V increments from battery voltage down to 2.65V.
TT Electronics/Optek Technology's Photologic V OPB9000 reflective optical sensor is used in industrial and medical applications to provide reliable edge and presence reflection media detection in a wide range of ambient light conditions. OPB9000, under the OPTEK brand, is suitable for a variety of applications including industrial printing, dispensing, manufacturing automation, safety and security equipment, and portable laboratory/medical equipment.
Microchip Technology Inc supplies the LAN8840 and LAN8841 Gigabit Ethernet transceiver devices that fulfil IEEE 1588v2 standards for Precision Timing Protocol. The Ethernet devices are enabled with Linux drivers and provide flexible Ethernet speed options, including 10BASE-T, 10BASE-Te, 100BASE-TX and 1000BASE-T.
Amphenol Communications Solutions’ ix Industrial Ethernet to RJ45 right-angle cable assemblies feature ND9 series connectors that provide a robust, miniaturized Ethernet interface (according to IEC 61076-3-124) with up to 75% space savings on the PCB compared to standard RJ45 jacks.
As a global leading supplier of positioning and wireless communication technologies and services, u-blox (SIX: UBXN) announced the launch of NORA-W3 module series products, further expanded its Wi Fi independent module product portfolio, and added dual band functions to this compact and compact product. NORA-W3 series has enhanced security protection function and is easy to integrate.
The Texas Instruments UCC21737-Q1 single-channel gate driver is an electrically isolated gate driver designed for use with SiC MOSFets and IGBTs at DC operating voltages up to 2121V, with advanced protection features, best-in-class dynamic performance and robustness. The device has a peak source and convergent current of up to ±10A.
Texas Instruments TPS56C231 12A synchronous step-down converter is a small, efficient, synchronous step-down converter with adaptive real-time D-CAP3 control mode. No external compensation is required because the device is easy to use and requires few external components. The device is ideal for space-constrained data center applications.
Texas Instruments TMUX7219-Q1 is a complementary metal oxide semiconductor (CMOS) switch with latched immunity. Single-channel 2:1 (SPDT) configuration works with single power supply (4.5V to 44v), dual power supply (± 4.5V to ±22v), or asymmetric power supply (for example, VDD=12v, VSS= -5v).
